Відео

Thanks for the video! I like the Beaver Dam kit...

Poke-MON

Please tell me that's a take beard

But everyone is going to die! Probably not right away, and not real dramatically!

Love it!!!😂😂😂

I would like to add something very important '''' after watching your ''clip'' i think that the best method is to ''rivet'' and weld the tanks on ''''' that way it the weld 'fails' the ''rivet's'' will add Extra ''sturdiness '' Also you can put (100) rivet's in each one ''''' it aint going to Fail'' not with 100 rivets & welded ''''''' WOW '''''' INDESTRUCTABLE '''''.

“Go deep throat a chainsaw” is my new go-to insult! Cheers brother!

This man is amazing 🤣🤣🤣 I can't stop laughing how have I not seen ur channel before?!? Minute 30 in and I'm subscribing 🤣 keep it up bro keep it up

the 3 stooges

First time watching and instantly hooked, love the honesty

i no engrish. serious though mericans need to think about how we butch our americaneese

Rivets and glue is good enough for Boeing, id say its okay for a johnboat...

Should you clean the lens from fingerprints before install ?

Your channel sucks. Still, I like watching.

5200 is a permanent bond adhesive that stuff is an amazing product

For those who really dont know, adhesives are way stronger than whatever they are holding together and stronger than bolts or nails or whatever

Your motor build was awesome! I'm building a yamaha 3 cylinder 2 stroke 25 hp into a beast! It's going on a 1554 prop tunnel. Still looking for the hull but I have the motor! I wish I could post pictures on UA-cam because it's pretty sexy!

First time viewer. That Haters Corner almost had me hitting the subscribe button, but 11:41 put me over the top and I smashed both the subscribe and like buttons :)

Idiots, foam removes flotation

I got a bluetti ac 200 max. It has a 12 volt 30 amp port. I wanna hardwired it to a dc control panel but scared ill screw it up lol.

If you had to say how much weight would you say was added by redoing the entire boat?

Your channel sucks. :)

will the gator glide prevent algae from growing on bottom of boat if it sits at a freshwater lake that is warm in summer my boat looks like it has carpet in a month of being in water

What’s a float pod.

The angle on your sides is too steep.... Either bring that angle to a point about 1 foot further up the boat, or cut them off flush and do without.... You're plowing through the water so bad it looks like elephant ears.... You'll get it...

The sky is falling is really popular these days.

Great video appreciate the patriotism and pep talk about doing it like a man the world is missing that these days

To get the power out of the little motors a GEAR reduction SETUP is what's needed Gear reduction needed to turn the prop 2-3xs faster than the RPM of the engine

I 3M 5200ed my 300hp outboard without issue

What size you put the pods on

This is such a helpful video, thank you brotha.

Why did you not paint the wood first?

Well sir you just got a new subscriber 😂 love it. Keep it up. haters gonna hate!

So are the pods still attached to the boat after 2 years?

I have a 12ft Alumacraft jon boat and just purchased a mud skipper rated for 5-7 horsepower engine. I'm going to get it at Harbor Freight, but I am just not sure which one I am suppose to get. Any help would be appreciated.

5200 is the bomb I used screws and 5200 to install a center console live well and ttop and never had an issue

Nice Tru story aluminum is light and floats naturally sturdy like steal light as a feather good video bruh thanx

I hear you,why are we not,the boats over there are wicked,I've built 3 different homemade mud motors,and planning asudacedrive but a Kia motor might be fun on a14ft

Is that the knockoff seadeck material from amazon? I bought some for a dock surface gonna put it on today or tomorrow, just wondering how it held up after 2 years?

Hey brother I got a tracker 1654 flat bottom with a Mercury 60 Bigfoot on the ass end let's go hunt some scooters

Great job

1030, 1032, 1036, 1040... ALL 10 Ft jon boat... but what is the best..?

I run an Exel , it came with built in pods , I’m an old man and it’s nice to have em to get on and off tha boat

Excellent review! Probably an ignorant question... Newbie here thinking of doing something like this. As cheap as the Predator engines are, or other Honda clones and how cost of upgrades can quickly add up to be more than the engines themselves, I thought it may make sense to buy 2 or 3 inexpensive engines, then tie them together to go to one of these kits. Is thereab adapter out there for this purpose, or with some creativity could one do a DIY hack. Or, is this just a bad idea for some reason?

"Land of Egg Rolls "😅

I don't always use proper grammar but brother, I love the sarcasm great channel

You rock bro

A business card is how everybody, including professionals set the coil gap that I know of... So the way you did it is just fine and dandy...

Man, I really hope I win this boat.

Mannnnnn I just lost my metric crescent wrench can I use my standard crescent wrench on this?😂😂😂😂😂😂😂😂😂😂😂